While the two acronyms are often used interchangeably, there’s a lot more to RNAV than just GPS.
RNAV, Defined
“Area Navigation” (RNAV) enables an aircraft to navigate between two points within the coverage zone of station-referenced navigation systems. Instead of having to follow a zig-zag pattern from one ground-based station to the next, RNAV allows aircraft to fly directly to any point within the coverage zone of the station in use. This “direct-to” capability often allows aircraft to bypass published routes, freeing up more airspace for traffic.
RNAV also enables aircraft to fly instrument approaches into airports that don’t have any ground-based navigation stations, such as a VOR or Localizer.
RNAV Routes Have Been Around Since The 1970s
The first RNAV en-route charts were published in 1968 when Narco introduced their CLC-60 RNAV computer to the market. This course line computer analyzed information from previously-installed VOR and DME receivers.
To use the CLC-60, two knobs controlled “radial” and “distance”. If you wanted to “move” the VOR station 12 miles out on the 180 radial (this is just like creating a waypoint 12 miles to the South of a VOR), you’d set “180” in the radial window and “12” in the distance window. Unlike a standard VOR instrument, a full-scale deflection on the CLC-60 was 2 miles, regardless of whether you were 1 mile or 50 miles from the station.
An RNAV route could be utilized by inputting a series of VOR Radials and DMEs to create a navigable course. Each “waypoint” of the course had an associated radial and DME from the VOR being used. Creating a direct route could shave off substantial mileage compared to victor airways, which rely on routes between NAVAIDs. However, to make this work, you needed to stay within the coverage limits of the VOR and DME.
Satellite Navigation (GPS)
The first GPS satellite was launched by the Department of Defense in 1978. Initially, GPS was only available for government and military use. But by 1993, a full 24-satellite constellation became operational and was opened to public use.
Using the same basic concept as VOR RNAV, as long as you’re within the coverage range of GPS reception and your receiver is functioning properly, you can navigate point to point. For an aircraft to obtain a 3D location, the GPS receiver must receive a reliable signal from 4 satellites simultaneously. With GPS available and accurate nearly all the time, it has become the go-to source for RNAV navigation.
An FMS Uses It All
Flight Management Systems (FMS), which are commonly found on business and airline jets, allow you to enter a series of waypoints and instrument procedures to define a flight route. If the waypoints and procedures are included in the navigation database, the computer calculates the distances and courses between all waypoints in the route. During flight, the FMS provides precise guidance between each pair of waypoints, along with real-time information about aircraft course, groundspeed, distance, estimated time between waypoints, fuel consumed, and fuel/flight time remaining. While most FMS systems use GPS, that’s not their only source of information.
Many FMS systems in large aircraft are linked to an Inertial Navigation Unit (often called an Inertial Reference System, or IRS), which consists of lasers and gyros that determine aircraft flight path, altitude, and attitude. And that’s not the only additional source of information for an FMS. Most FMS systems can use GPS, IRS, VOR, LOC, and DME receivers to provide position information to the FMS. If one form of navigation becomes unreliable, backup navigation aids can be used to obtain continuous position information.
Live from the Flight Deck
Approved RNAV Systems, And When To Use Them
According to the AIM, these are a few RNAV systems that can be approved. Keep in mind, the specific equipment and certification go beyond this list:
– Approved GPS Receivers
– Flight Management Systems Integrating Multiple Navigation Sensors
– RNAV System with DME/DME/IRU
DME/DME/IRU systems don’t rely on GPS and instead utilize multiple DME stations and an Inertial Reference Unit to obtain position information. While GPS may initially provide the IRU with location information for calibration, it doesn’t rely on GPS for operation.
What About RNP?
Required Navigation Performance (RNP) is a form of navigation that allows an aircraft to fly directly between two 3D points in space. The fundamental difference between RNP and RNAV is that RNP requires on-board performance monitoring and alerting capability. Think of it as a computer system that constantly self-assesses and ensures the reliability of navigation signals and position information.
According to GE Aviation, “RNP approaches with RNP values down to 0.1 allow aircraft to follow precise three-dimensional curved flight paths through congested airspace, around noise sensitive areas, or through difficult terrain.” Specific testing and equipment are required to become RNP certified. Generally speaking, you won’t fly RNP procedures unless you’re flying airline or corporate aircraft.
So, Does RNAV Always Mean GPS?
For most general aviation pilots today, yes. While GPS doesn’t automatically equal RNAV, it’s the most common system found in cockpits around the world, especially for piston aircraft.